Questo sito utilizza cookie tecnici e di terze parti per fornire all'utente un servizio migliore. Continuando con la navigazione accetti l'utilizzo dei cookies sul nostro sito web. Clicca per maggiori informazioni Continua

Whether you ride a small scooter or a powerful superbike, whether your passion is for jet skis or snowmobiles, our new Motor Energy range of batteries gives you the concentrated and reliable power you need. For passion, sport or utility, say ‘Yes’ to Motor Energy.

What’s your MOTOR ENERGY?

FIND OUT

MOTOR ENERGY

SEALED VALVE-REGULATED GAS-RECOMBINATION BATTERY

Absorbed Glass Mat (AGM) technology eliminates dangerous leakages of electrolyte by using a very fine fibreglass separator which absorbs the electrolyte withholding it inside the battery. No risk of acid leakage during installation or use.

OUTSTANDING STARTING POWER

Top power for safe starts in all conditions. The starting efficiency (A)/weight (kg) ratio of AGM batteries is the highest available today.

MAINTENANCE-FREE

The implemented technology cuts water consumption virtually to zero. No top-ups needed for the entire life of the battery.

RESISTANCE TO VIBRATIONS

The plate-mats are compressed and construction is perfected to make the batter y extremely resistant to vibrations for a longer life.

See moreTECHNOLOGY AGM

DRY CHARGE BATTERIES WITH ACID BOTTLE INCLUDED

The advantage is that the battery can be activated whenever it is needed. Dry charge batteries can be stored for a long time. The acid bottle provided with the battery allows it to be prepared for use at any time.

FB TECHNOLOGY

Top starting power, always. Special additives specifically formulated to reduce damage caused by sulphation of plates during deep discharge of the battery, guaranteeing starting even in difficult conditions. (This technology is implemented in all FB models).Top power for safe starts in all conditions. The starting efficiency (A)/weight (kg) ratio of AGM batteries is the highest available today.

LOW MAINTENANCE

A special lead alloy reduces water consumption, the self-discharge of the battery and need for maintenance, as a consequence.

COMPLETE RANGE: 12 V & 6 V

More than 50 models of batteries for all types of motorbikes.

ApplicationsApplicationsApplications

SCOOTER

  • Maximum starting performance even in cold weather
  • High vibration resistance for maximum reliability and duration
  • Low maintenance

MOTORCYCLE

  • High peak power for easy starting even with the biggest engines
  • Excellent vibration resistance
  • Maintenance-free

ATV

  • High energy starting power
  • Ideal for extreme conditions
  • High impact resistance
  • No risk of electrolyte spillage at acute angles or as a result of falls

SNOWMOBILE

  • The charge and current you need for starting even in extreme temperatures
  • High impact resistance

JET SKY

  • Excellent corrosion and impact resistance
  • No risk of electrolyte spillage at acute angles or as a result of falls

INSTRUCTIONS FOR ACTIVATING, CHARGING AND INSTALLING THE FLOODED BATTERY

  1. Position the battery on a flat surface. Remove the upper caps and the breather cap.
  2. Remove the protective film from the acid container.
  3. Cut the acid container and apply the tube provided.
  4. Insert the tube into each hole in the battery and slowly pour in the acid up to the UPPER LEVEL (no higher).
  5. Position the caps on the holes and let the battery stand for 30 minutes for the plates to activate.
  6. Press or screw the caps back fully. Leave the breather cap open.
  7. The battery charge state will be about 70-80% after activation. Recharging is always recommended to install a fully charged battery.
  8. Apply the breather tube (if provided).
  9. Check that the tube is intact and not squeezed. Check that connection to the electric system is correct. Check that the fastening screws are tight.
DownloadPDF
  1. Position the battery on a flat surface. Remove the upper caps and the breather cap.
  2. Remove the protective film from the acid container.
  3. Cut the acid container and apply the tube provided.
  4. Insert the tube into each hole in the battery and slowly pour in the acid up to the UPPER LEVEL (no higher).
  5. Position the caps on the holes and let the battery stand for 30 minutes for the plates to activate.
  6. Press or screw the caps back fully. Leave the breather cap open.
  7. The battery charge state will be about 70-80% after activation. Recharging is always recommended to install a fully charged battery.
  8. Apply the breather tube (if provided).
  9. Check that the tube is intact and not squeezed. Check that connection to the electric system is correct. Check that the fastening screws are tight.
DOWNLOADPDF